Water Quality

Abstract:

According to the different statistical tools it was possible to define that in laboratory the volume of 1 drop is 0.026054 ml, it was concluded that the calculations are representative because the propagation of errors for calculation of volume of 1 drop is 0.005482 ml. Finally, the number of moles and number of drops of H2O needed to have 0.5 atm vapor pressure in 1 liter. 11.48022 drops and 0.016347 moles

Don't use plagiarized sources. Get Your Custom Essay on
Water Quality
Just from $13/Page
Order Essay

 

Introduction:

All experimental measurements are affected by an inherent imprecision in the measurement process. Since this is basically a matter of comparing with a standard and this comparison is made with an apparatus, the measurement will depend on the minimum quantity that it is able to measure. And this amount is decreasing with the progress of physics in a continuous process, but with no apparent end. That is, although each time we can give the measure with more “decimals”, the next “decimal” will not be known.

 

 

Procedure and Results:

  1. Table 1
Table 1
Trial V, ml DV, ml m, g Dm, g
1 1 1 26.6384 0.8097
2 1.6 0.6 27.3222 0.6838
3 2.1 0.5 27.9214 0.5992
4 3 0.9 28.657 0.7356
5 3.8 0.8 29.4867 0.8297
6 4.4 0.6 30.2572 0.7705
7 5.2 0.8 30.9415 0.6843
8 6 0.8 31.6862 0.7447
9 6.8 0.8 32.5244 0.8382

 

  • Q-test for all experimental data.
Q tests
Trial DV Dm
1 0.103448 0.116174
2 0.086207 0.101801
3 0.086207 0.101801
4 0.137931 0.124975
5 0.103448 0.130904
6 0.103448 0.116259
7 0.137931 0.116259
8 0.137931 0.142406
9 0.137931 0.142406

 

 

 

 

  • Standard deviations, standard errors of mean and C.L. for volume and mass:

Table 2

  DV, ml Dm, g
Mean 0.755556 0.743967
Std dev, Sx 0.15899 0.078631
Error of mean, dx 0.052997 0.02621
C.L. 0.122422 0.060546
  • Mean density of watercalculated using mean volume from cylinder readings and mean masses from analytical balance measurements.984662 g/ml
  • Propagation of errors for density calculations above.231868 g/ml
  • Plot (m vs V) and Linest (Excel) data.
LINEST data

 

1.004782 25.7081
0.013518 0.057007
0.998735 0.0769
5524.627 7
32.67025 0.041395

 

  • Tabulate results:

Table 3

r ± C.L. (from mean Dm and DV), g/ml r ± C.L. (from plot), g/ml
(9.85± 2.32) * 10-1 1.00± 0.01
  • You should round off the reported values. How many digits should you report in final answer for analytical balance? Points will be taken off for incorrect rounding.
  • The order of magnitude of the result should be as clear as possible. Therefore, the preferred notation of for instance 0174 ± 0.0002 is (1.74 ± 0.02)·10-2.
  • Volume of 1 drop.026054 ml
  • Propagation of errors for calculation of volume of 1 drop.005482 ml
  • Number of moles and number of drops of H2O needed to have 0.5 atm vapor pressure in 1 liter.48022 drops and 0.016347 moles

(This data will be needed for your future experiments)

 

Discussion:

 

Different variations in laboratory measurements can be found due to the errors listed below.

Instrumental errors (of apparatus): for example, the calibration error of the instruments.

– Personal error: This is, in general, difficult to determine and is due to personal limitations. Like, for example, parallax errors, or visual problems.

– Measurement method errors, which correspond to an inappropriate choice of the measurement method; This includes three different possibilities: the inadequacy of the measuring device, the observer, or the measurement method itself.

Statistical tools allow from a database, to define the its trend based on other variables. However, the purpose is to find a trend that perfectly describes the phenomenon. Therefore, with a defined trend and an explained phenomenon, measurements can be ruled out as incorrect.Also in the case of having many measurements, the value that is most representative of the group studied could be defined.

 

References:

https://en.wikipedia.org/wiki/Standard_error

https://www.itl.nist.gov/div898/handbook/eda/section3/eda352.htm

https://www.itl.nist.gov/div898/handbook/mpc/section5/mpc55.htm

https://en.wikipedia.org/wiki/Propagation_of_uncertainty

https://chem.libretexts.org/Textbook_Maps/General_Chemistry/Book%3A_ChemPRIME_(Moore_et_al.)/01Introduction%3A_The_Ambit_of_Chemistry/1.06%3A_Errors_in_Measurement

 

Homework Writing Bay
Calculator

Calculate the price of your paper

Total price:$26
Our features

We've got everything to become your favourite writing service

Need a better grade?
We've got you covered.

Order your paper